M Surface Finishes | 39 | v138 | Spon's Architects' and Builders' Pric

ABSTRACT

M10 CEMENT: SAND/CONCRETE SCREEDS/ GRANOLITHIC SCREEDS/TOPPING

Cement and sand (1:3) screeds; steel trowelled Work to ﬂoors; one coat level; to concrete base; screeded; over 300mm wide

25mm thick – – – – m2 8.21 50mm thick – – – – m2 9.72 75mm thick – – – – m2 12.86 100mm thick – – – – m2 16.00

Add to the above for work to falls and crossfalls and to slopes

not exceeding 15° from horizontal – 0.02 0.39 – m2 0.39 over 15° from horizontal – 0.09 1.77 – m2 1.77 water repellent additive incorporated in the mix – 0.02 0.39 3.43 m2 3.82 oil repellent additive incorporated in the mix – 0.07 1.37 3.64 m2 5.01

Fine concrete (1: 4-5) levelling screeds; steel trowlelled Work to ﬂoors; one coat; level; to concrete base; over 300mm wide

50mm thick – – – – m2 9.72 75mm thick – – – – m2 12.86

Extra over last for isolation joint to perimeter – – – – m 1.12

Early drying ﬂoor screed; RMC Mortars Readyscreed; or other equal and approved; steel trowlelled Work to ﬂoors; one coat; level; to concrete base; over 300mm wide

100mm thick – – – – m2 18.05 Extra over last for galvanized chicken wire anticrack reinforcement – – – – m2 0.85

Granolithic paving; cement and granite chippings 5 to dust (1:1:2); steel trowelled Work to ﬂoors; one coat; level; laid on concrete while green; bonded; over 300mm wide

25mm thick – – – – m2 22.12 38mm thick – – – – m2 24.62

Work to ﬂoors; two coat; laid on hacked concrete with slurry; over 300mm wide

50mm thick – – – – m2 27.23 75mm thick – – – – m2 33.52

Work to landings; one coat; level; laid on concrete while green; bonded; over 300mm wide

25mm thick – – – – m2 33.09 38mm thick – – – – m2 36.94

Total £ hours £ £ rate £

M10 CEMENT: SAND/CONCRETE SCREEDS/ GRANOLITHIC SCREEDS/TOPPING – cont

Granolithic paving – cont Work to landings; two coat; laid on hacked concrete with slurry; over 300mm wide

50mm thick – – – – m2 40.84 75mm thick – – – – m2 50.27

Add to the above over 300mm wide for liquid hardening additive incorporated in the mix – 0.04 0.79 0.39 m2 1.18 oil-repellent additive incorporated in the mix – 0.07 1.37 3.64 m2 5.01

25mm work to treads; one coat; to concrete base 225mm wide – 0.83 16.34 8.11 m 24.45 275mm wide – 0.83 16.34 9.07 m 25.41 returned end – 0.17 3.34 – nr 3.34

13mm skirtings; rounded top edge and coved bottom junction; to brickwork or blockwork base

75mm wide on face – 0.51 10.03 0.39 m 10.42 150mm wide on face – 0.69 13.58 7.13 m 20.71 ends; fair – 0.04 0.79 – nr 0.79 angles – 0.06 1.18 – nr 1.18

13mm outer margin to stairs; to follow proﬁle of and with rounded nosing to treads and risers; fair edge and arris at bottom, to concrete base

75mm wide – 0.83 16.34 3.88 m 20.22 angles – 0.06 1.18 – nr 1.18

13mm wall string to stairs; fair edge and arris on top; coved bottom junction with treads and risers; to brickwork or blockwork base

275mm (extreme) wide – 0.74 14.57 6.81 m 21.38 ends – 0.04 0.79 – nr 0.79 angles – 0.06 1.18 – nr 1.18 ramps – 0.07 1.37 – nr 1.37 ramped and wreathed corners – 0.09 1.77 – nr 1.77

13mm outer string to stairs; rounded nosing on top at junction with treads and risers; fair edge and arris at bottom; to concrete base

300mm (extreme) wide – 0.74 14.57 8.43 m 23.00 ends – 0.04 0.79 – nr 0.79 angles – 0.06 1.18 – nr 1.18 ramps – 0.07 1.37 – nr 1.37 ramps and wreathed corners – 0.09 1.77 – nr 1.77

19mm thick skirtings; rounded top edge and coved bottom junction; to brickwork or blockwork base

75mm wide on face – 0.51 10.03 7.13 m 17.16 150mm wide on face – 0.69 13.58 11.02 m 24.60 ends; fair – 0.04 0.79 – nr 0.79 angles – 0.06 1.18 – nr 1.18

Total £ hours £ £ rate £

19mm riser; one rounded nosing; to concrete base 150mm high; plain – 0.83 16.34 6.16 m 22.50 150mm high; undercut – 0.83 16.34 6.16 m 22.50 180mm high; plain – 0.83 16.34 8.43 m 24.77 180mm high; undercut – 0.83 16.34 8.43 m 24.77

M11 MASTIC ASPHALT FLOORING/FLOOR UNDERLAYS

Mastic asphalt ﬂooring to BS 6925 Type F 1076; black 20mm thick; one coat coverings; felt isolating membrane; to concrete base; ﬂat

over 300mm wide – – – – m2 17.50 225mm-300mm wide – – – – m2 32.51 150mm-225mm wide – – – – m2 35.70 not exceeding 150mm wide – – – – m2 43.70

25mm thick; one coat coverings; felt isolating membrane; to concrete base; ﬂat

over 300mm wide – – – – m2 20.31 225mm-300mm wide – – – – m2 34.67 150mm-225mm wide – – – – m2 37.79 not exceeding 150mm wide – – – – m2 45.81

20mm three coat skirtings to brickwork base not exceeding 150mm girth – – – – m 17.87 150mm-225mm girth – – – – m 21.85 225mm-300mm girth – – – – m 25.83

Mastic asphalt ﬂooring; acid-resisting; black 20mm thick; one coat coverings; felt isolating membrane; to concrete base ﬂat

over 300mm wide – – – – m2 20.49 225mm-300mm wide – – – – m2 37.48 150mm-225mm wide – – – – m2 38.71 not exceeding 150mm wide – – – – m2 46.70

25mm thick; one coat coverings; felt isolating membrane; to concrete base; ﬂat

over 300mm wide – – – – m2 24.21 225mm-300mm wide – – – – m2 38.53 150mm-225mm wide – – – – m2 41.71 not exceeding 150mm wide – – – – m2 49.72

20mm thick; three coat skirtings to brickwork base not exceeding 150mm girth – – – – m 18.06 150mm-225mm girth – – – – m 21.04 225mm-300mm girth – – – – m 23.88

Total £ hours £ £ rate £

M11 MASTIC ASPHALT FLOORING/FLOOR UNDERLAYS – cont

Mastic asphalt ﬂooring to BS 6925 Type F 1451; red 20mm thick; one coat coverings; felt isolating membrane; to concrete base; ﬂat

over 300mm wide – – – – m2 28.67 225mm-300mm wide – – – – m2 47.37 150mm-225mm wide – – – – m2 51.16 not exceeding 150mm wide – – – – m2 61.21

20mm thick; three coat skirtings to brickwork base not exceeding 150mm girth – – – – m 22.51 150mm-225mm girth – – – – m 28.67

M12 TROWELLED BITUMEN/RESIN/RUBBER LATEX

Latex cement ﬂoor screeds; steel trowelled Work to ﬂoors; level; to concrete base; over 300mm wide

3mm thick; one coat – – – – m2 3.95 5mm thick; two coats – – – – m2 5.50

Resin ﬂooring; Altro or other equal and approved; steel trowelled Work to ﬂoors; level; to concrete base; over 300mm wide

AltroTect clear; up to 3mm thick; two coat – – – – m2 6.52 AltroTect coloured; up to 3mm thick; two coat – – – – m2 6.91 AltroFlow EP 1000; up to 3mm thick; two coat – – – – m2 15.12 AltroFlow EP 2000; up to 3mm thick; two coat – – – – m2 24.08 AltroFlow EP 3000; up to 3mm thick; two coat – – – – m2 30.88 AltroScreed Quartz EP; 4-6mm thick – – – – m2 37.87 Altro SoloSafe; 5-6mm thick – – – – m2 55.47 Altro MultiScreed; 4mm thick – – – – m2 34.04 Altrocrete PU (Polyurethane); 2-9mm thick – – – – m2 32.51

Isocrete K screeds or other equal and approved; steel trowelled Work to ﬂoors; level; to concrete base; over 300mm wide

35mm thick; plus polymer bonder coat – – – – m2 11.98 40mm thick – – – – m2 11.06 45mm thick – – – – m2 11.69 50mm thick – – – – m2 12.32

Work to ﬂoors; to falls or cross-falls; to concrete base; over 300mm wide

55mm (average) thick – – – – m2 12.94 60mm (average) thick – – – – m2 13.58 m2 m2 m2

Total £ hours £ £ rate £

Isocrete K screeds; quick drying; or other equal and approved; steel trowelled Work to ﬂoors; level or to ﬂoors n.e. 15° frojm the horizontal; to concrete base; over 300mm wide

55mm thick – – – – m2 16.76 75mm thick – – – – m2 20.94

Isocrete pumpable Self Level Plus screeds; or other equal and approved; protected with Corex type polythene; knifed off prior to laying ﬂoor ﬁnish; ﬂat smooth ﬁnish Work to ﬂoors; level or to ﬂoors n.e. 15° frojm the horizontal; to concrete base; over 300mm wide

20mm thick – – – – m2 20.42 50mm thick – – – – m2 27.23

Bituminous lightweight insulating roof screeds Bit-Ag or similar roof screed or other equal and approved; to falls or cross-falls; bitumen felt vapour barrier; over 300mm wide

75mm (average) thick – – – – m2 45.99 100mm (average) thick – – – – m2 58.28

M20 PLASTERED/RENDERED/ROUGHCAST COATING

Cement and sand (1:3) beds and backings 10mm thick work to walls; one coat; to brickwork or blockwork base

over 300mm wide – – – – m2 13.51 not exceeding 300mm wide – – – – m 6.76

13mm thick; work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 16.25 not exceeding 300mm wide – – – – m 8.14

15mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 17.51 not exceeding 300mm wide – – – – m 8.77

Cement and sand (1:3); steel trowelled 13mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 14.14 not exceeding 300mm wide – – – – m 7.07

16mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 15.84 not exceeding 300mm wide – – – – m 7.93

Total £ hours £ £ rate £

M20 PLASTERED/RENDERED/ROUGHCAST COATING – cont

Cement and sand (1:3) – cont 19mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 18.32 not exceeding 300mm wide – – – – m 9.16

ADD to above over 300mm wide in water repellent cement – – – – m2 3.75 ﬁnishing coat in colour cement – – – – m2 7.99

Cement-lime-sand (1:2:9); steel trowelled 19mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 17.77 not exceeding 300mm wide – – – – m 8.89

Cement-lime-sand (1:1:6); steel trowelled 13mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 14.54 not exceeding 300mm wide – – – – m 7.16

Add to the above over 300mm wide for waterproof additive – – – – m2 2.45

19mm thick work to ceilings; three coats; to metal lathing base

over 300mm wide – – – – m2 17.09 not exceeding 300mm wide – – – – m 9.99

Sto External render only system; comprising glassﬁbre mesh reinforcement embedded in 10mm Sto Levell Cote with Sto Armat Classic Basecoat Render and Stolit K 1.5 Decorative Topcoat Render (white) 15mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 41.72 Extra for

bellcast bead – – – – m 3.97 external angle with PVC mesh angle bead – – – – m 3.66 internal angle with Sto Armor angle – – – – m 3.66 render stop bead – – – – m 3.66

K-Rend render or similar through-colour render system 18mm thick work to walls; two coats; to brickwork or blockwork base; ﬁrst coat 8mm standard base coat; second coat 10mm K-rend silicone WP/FT

Total £ hours £ £ rate £

Plaster; ﬁrst 11mm coat of Thistle Hardwall plaster; second 2mm ﬁnishing coat of Thistle Multi Finish plaster; steel trowelled 13mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 11.21 over 300mm wide; in staircase areas or plant rooms – – – – m2 13.47 not exceeding 300mm wide – – – – m 5.96

13mm thick work to isolated brickwork or blockwork columns; two coats

over 300mm wide – – – – m2 21.12 not exceeding 300mm wide – – – – m 10.56

Plaster; ﬁrst 11mm coat of Thistle Browning plaster; second ﬁnishing coat of 2mm Thistle Multi Finish plaster; steel trowelled ﬁnish 13mm thick; work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 11.21 over 300mm wide; in staircase areas or plant rooms – – – – m2 13.46 not exceeding 300mm wide – – – – m 5.96

13mm thick work to isolated brickwork or blockwork columns; two coats

over 300mm wide – – – – m2 21.12 not exceeding 300mm wide – – – – m 9.36

Plaster; ﬁrst 8mm or 11mm coat of Thistle Bonding plaster; second 2mm ﬁnishing coat of Thistle Multi Finish plaster; steel trowelled ﬁnish 13mm thick work to walls; two coats; to concrete base

over 300mm wide – – – – m2 12.55 over 300mm wide; in staircase areas or plant rooms – – – – m2 14.87 not exceeding 300mm wide – – – – m 5.75

13mm thick work to isolated piers or columns; two coats; to concrete base

over 300mm wide – – – – m2 22.43 not exceeding 300mm wide – – – – m 10.50

10mm thick work to ceilings; two coats; to concrete base

over 300mm wide – – – – m2 10.74 over 300 wide; 3.50m-5.00m high – – – – m2 12.89 over 300mm wide; in staircase areas or plant rooms – – – – m2 14.26 not exceeding 300mm wide – – – – m 6.00

Total £ hours £ £ rate £

M20 PLASTERED/RENDERED/ROUGHCAST COATING – cont

Plaster – cont 10mm thick work to isolated beams; two coats; to concrete base

over 300mm wide – – – – m2 21.48 over 300mm wide; 3.50m-5.00m high – – – – m2 22.91 not exceeding 300mm wide – – – – m 10.80

Plaster; one coat Snowplast plaster or other equal and approved; steel trowelled 13mm thick work to walls; one coat; to brickwork or blockwork base

over 300mm wide – – – – m2 12.40 over 300mm wide; in staircase areas or plant rooms – – – – m2 14.73 not exceeding 300mm wide – – – – m 6.21

13 thick work to isolated columns; one coat over 300mm wide – – – – m2 15.00 not exceeding 300mm wide – – – – m 7.53

Plaster; ﬁrst coat of Limelite renovating plaster; ﬁnishing coat of Limelite ﬁnishing plaster; or other equal and approved; steel trowelled 13mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 17.19 over 300mm wide; in staircase areas or plant rooms – – – – m2 18.87 not exceeding 300mm wide – – – – m 8.60

Dubbing out existing walls with undercoat plaster; average 6mm thick

over 300mm wide – – – – m2 5.16 not exceeding 300mm wide – – – – m 2.61

Dubbing out existing walls with undercoat plaster; average 12mm thick

over 300mm wide – – – – m2 10.31 not exceeding 300mm wide – – – – m 5.16

Plaster; ﬁrst coat of Thistle X-ray plaster or other equal and approved; ﬁnishing coat of Thistle X-ray ﬁnishing plaster or other equal and approved; steel trowelled 17mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 55.79 over 300mm wide; in staircase areas or plant rooms – – – – m2 59.94 m

Total £ hours £ £ rate £

17mm thick work to isolated columns; two coats over 300mm wide – – – – m2 90.50 not exceeding 300mm wide – – – – m 36.17

Plaster; one coat Thistle projection plaster or other equal and approved; steel trowelled 13mm thick work to walls; one coat; to brickwork or blockwork base

over 300mm wide – – – – m2 11.96 over 300mm wide; in staircase areas or plant rooms – – – – m2 13.68 not exceeding 300mm wide – – – – m 5.97

10mm thick work to isolated columns; one coat over 300mm wide – – – – m2 14.56 not exceeding 300mm wide – – – – m 7.26

Plaster; ﬁrst 11mm coat of Thistle Bonding plaster; second 2mm ﬁnishing coat of Thistle Multi Finish plaster; steel trowelled 13mm thick work to ceilings; three coats to metal lathing base

over 300mm wide – – – – m2 13.03 over 300mm wide; in staircase areas or plant rooms – – – – m2 15.63 not exceeding 300mm wide – – – – m 7.03

13mm thick work to swept sofﬁt of metal lathing arch former

not exceeding 300mm wide – – – – m 9.38 300mm-400mm wide – – – – m 12.54

13mm thick work to vertical face of metal lathing arch former

not exceeding 0.50m2 per side – – – – nr 13.32 0.50m2 – 1m2 per side – – – – nr 19.98

Cemrend self-coloured render or other equal and approved; one coat; to brickwork or blockwork base 20mm thick work to walls; to brickwork or blockwork base

over 300mm wide – – – – m2 28.35 not exceeding 300mm wide – – – – m 16.65

Tyrolean decorative rendering or similar; 13mm thick ﬁrst coat of cement-lime-sand (1:1:6); ﬁnishing three coats of Cullamix or other equal and approved; applied with approved hand operated machine external To walls; four coats; to brickwork or blockwork base

over 300mm wide – – – – m2 28.59 m

Total £ hours £ £ rate £

M20 PLASTERED/RENDERED/ROUGHCAST COATING – cont

Drydash (pebbledash) ﬁnish of Derbyshire Spar chippings or other equal and approved on and including cement-lime-sand (1:2:9) backing 18mm thick work to walls; two coats; to brickwork or blockwork base

over 300mm wide – – – – m2 24.78 not exceeding 300mm wide – – – – m 12.40

Plaster; one coat Thistle board ﬁnish or other equal and approved; steel trowelled (prices included within plasterboard rates) 3mm thick work to walls or ceilings; one coat; to plasterboard base

over 300mm wide – – – – m2 5.06 over 300mm wide; in staircase areas or plant rooms – – – – m2 6.07 not exceeding 300mm wide – – – – m 2.02

Plaster; one coat Thistle board ﬁnish or other and approved; steel trowelled 3mm work to walls or ceilings; one coat on and including gypsum plasterboard; BS 1230; ﬁxing with nails; 3mm joints ﬁlled with plaster and jute scrim cloth; to softwood base; plain grade baseboard or lath with rounded edges 9.50mm thick boards to walls

over 300mm wide – 0.97 12.93 3.29 m2 16.22 not exceeding 300mm wide – 0.37 5.20 0.94 m 6.14

9.50mm thick boards to walls; in staircase areas or plant rooms

over 300mm wide – 1.06 14.19 3.29 m2 17.48 not exceeding 300mm wide – 0.46 6.46 0.94 m 7.40

9.50mm thick boards to isolated columns over 300mm wide – 1.06 14.19 3.29 m2 17.48 not exceeding 300mm wide – 0.56 7.86 0.94 m 8.80

9.50mm thick boards to ceilings over 300mm wide – 0.89 11.81 3.29 m2 15.10 over 300mm wide; 3.50m-5.00m high – 1.03 13.77 3.29 m2 17.06 not exceeding 300mm wide – 0.43 6.04 0.94 m 6.98

9.50mm thick boards to ceilings; in staircase areas or plant rooms

over 300mm wide – 0.98 13.07 3.29 m2 16.36 not exceeding 300mm wide – 0.47 6.59 0.94 m 7.53

9.50mm thick boards to isolated beams over 300mm wide – 1.05 14.05 3.29 m2 17.34 not exceeding 300mm wide – 0.50 7.02 0.94 m 7.96

Total £ hours £ £ rate £

12.50mm thick boards to walls; in staircase areas or plant rooms

over 300mm wide – 1.12 15.04 3.29 m2 18.33 not exceeding 300mm wide – 0.50 7.02 0.94 m 7.96

12.50mm thick boards to isolated columns over 300mm wide – 1.12 15.04 3.29 m2 18.33 not exceeding 300mm wide – 0.59 8.28 0.94 m 9.22

12.50mm thick boards to ceilings over 300mm wide – 0.95 12.65 3.29 m2 15.94 over 300mm wide; 3.50m-5.00m high – 1.06 14.19 3.29 m2 17.48 not exceeding 300mm wide – 0.45 6.31 0.94 m 7.25

12.50mm thick boards to ceilings; in staircase areas or plant rooms

over 300mm wide – 1.06 14.19 3.29 m2 17.48 not exceeding 300mm wide – 0.51 7.15 0.94 m 8.09

12.50mm thick boards to isolated beams over 300mm wide – 1.15 15.46 3.29 m2 18.75 not exceeding 300mm wide – 0.56 7.86 0.94 m 8.80

Accessories Expamet render beads or other equal and approved; white PVC nosings; to brickwork or blockwork base

external stop bead; ref 573 – 0.07 0.98 5.29 m 6.27 Expamet render beads or other equal and approved; stainless steel; to brickwork or blockwork base

stop bead; ref 546 – 0.07 0.98 4.34 m 5.32 stop bead; ref 547 – 0.07 0.98 4.33 m 5.31

Expamet plaster beads or other equal and approved; galvanized steel; to brickwork or blockwork base

angle bead; ref 550 – 0.08 1.13 1.12 m 2.25 architrave bead; ref 579 – 0.10 1.40 3.05 m 4.45 stop bead; ref 562 – 0.07 0.98 1.37 m 2.35 stop beads; ref 563 – 0.07 0.98 1.91 m 2.89 movement bead; ref 588 – 0.09 1.26 10.69 m 11.95

Expamet plaster beads or other equal and approved; stainless steel; to brickwork or blockwork base

angle bead; ref 545 – 0.08 1.13 4.87 m 6.00 stop bead; ref 534 – 0.07 0.98 4.34 m 5.32 stop bead; ref 533 – 0.07 0.98 4.34 m 5.32

Expamet thin coat plaster beads or other equal and approved; galvanized steel; to timber base

angle bead; ref 553 – 0.07 0.98 1.05 m 2.03 stop bead; ref 560 – 0.06 0.84 1.59 m 2.43 stop bead; ref 561 – 0.06 0.84 1.59 m 2.43

Total £ hours £ £ rate £

M21 INSULATION WITH RENDERED FINISH

Sto Therm Classic M-system insulation render 70mm EPS insulation ﬁxed with adhesive to SFS structure (measured separately) with horizontal PVC intermediate track and vertical T-spines; with glassﬁbre mesh reinforcement embedded in Sto Armat Classic Basecoat Render and Stolit K 1.5 Decorative Topcoat Render (white)

over 300mm wide – – – – m2 49.52 70mm EPS insulation mechanically ﬁxed to SFS structure (measured separately) with horizontal PVC intermediate track and vertical T-spines; with glassﬁbre mesh reinforcement embedded in Sto Armat Classic Basecoat Render and Stolit K 1.5 Decorative Topcoat Render (white)

over 300mm wide – – – – m2 54.48 rendered heads and reveals not exceeding 100mm wide; including angle beads – – – – m 13.68

Extra for aluminium starter track at base of insulated render system – – – – m 8.32 external angle with PVC mesh angle bead – – – – m 3.66 internal angle with Sto Armor angle – – – – m 3.66 render stop bead – – – – m 3.66 Sto seal tape to all vertical abutments – – – – m 3.41

Sto Armor mat HD mesh reinforcement to areas prone to physical damage (e.g. 1800mm high adjoining ﬂoor level)

over 300mm wide – – – – m2 10.96

M22 SPRAYED MINERAL FIBRE COATINGS

Prepare and apply by spray Mandolite CP2 ﬁre protection or other equal and approved on structural steel/metalwork 16mm thick (one hour) ﬁre protection

to walls and columns – – – – m2 8.48 to ceilings and beams – – – – m2 9.35 to isolated metalwork – – – – m2 18.65

22mm thick (one and a half hour) ﬁre protection to walls and columns – – – – m2 9.86 to ceilings and beams – – – – m2 10.94 to isolated metalwork – – – – m2 21.87

28mm thick (two hour) ﬁre protection to walls and columns – – – – m2 11.56 to ceilings and beams – – – – m2 12.63 to isolated metalwork – – – – m2 25.25

52mm thick (four hour) ﬁre protection m2 m2 m2

Total £ hours £ £ rate £

Prepare and apply by spray; cementitious Pyrok WF26 render or other equal and approved; on expanded metal lathing (not included) 15mm thick

to ceilings and beams – – – – m2 26.83

M30 METAL MESH LATHING/ANCHORED REINFORCEMENT FOR PLASTERED COATINGS

Accessories Preformed galvanized expanded steel semi-circular arch-frames; Expamet or other equal and approved; to suit walls up to 230mm thick

for 760mm opening; ref ESC 30 72.56 0.46 5.82 74.37 nr 80.19 for 840mm opening; ref ESC 32 73.75 0.46 5.82 75.59 nr 81.41 for 920mm opening; ref ESC 36 89.13 0.46 5.82 91.36 nr 97.18 for 1220mm opening; ref ESC 48 111.08 0.46 5.82 113.86 nr 119.68

Lathing; Expamet BB expanded metal lathing or other equal and approved; BS EN 13658; 50mm laps 6mm thick mesh linings to ceilings; ﬁxing with staples; to softwood base; over 300mm wide

ref BB263; 0.500mm thick 6.88 0.56 7.09 7.05 m2 14.14 ref BB264; 0.675mm thick 9.63 0.56 7.09 9.87 m2 16.96

6mm thick mesh linings to ceilings; ﬁxing with wire; to steelwork; over 300mm wide

ref BB263; 0.500mm thick – 0.59 7.48 7.05 m2 14.53 ref BB264; 0.675mm thick – 0.59 7.48 9.87 m2 17.35

6mm thick mesh linings to ceilings; ﬁxing with wire; to steelwork; not exceeding 300mm wide

ref BB263; 0.500mm thick – 0.37 4.67 7.05 m2 11.72 ref BB264; 0.675mm thick – 0.37 4.67 9.87 m2 14.54 raking cutting – 0.19 2.67 – m 2.67 cutting and ﬁtting around pipes; not exceeding 0.30m girth – 0.28 3.93 – nr 3.93

Lathing; Expamet Riblath or Spraylath or other equal and approved stiffened expanded metal lathing or similar; 50mm laps 10mm thick mesh lining to walls; ﬁxing with nails; to softwood base; over 300mm wide

Riblath ref 269; 0.30mm thick 14.45 0.46 5.82 14.89 m2 20.71 Riblath ref 271; 0.50mm thick 11.38 0.46 5.82 11.75 m2 17.57

10mm thick mesh lining to walls; ﬁxing with nails; to softwood base; not exceeding 300mm wide

Riblath ref 269; 0.30mm thick – 0.28 3.55 4.50 m2 8.05 Riblath ref 271; 0.50mm thick – 0.28 3.55 3.56 m2 7.11

Total £ hours £ £ rate £

M30 METAL MESH LATHING/ANCHORED REINFORCEMENT FOR PLASTERED COATINGS – cont

Lathing – cont 10mm thick mesh lining to walls; ﬁxing to brick or blockwork; over 300mm wide

Red-rib ref 274; 0.50mm thick 14.45 0.37 4.67 15.71 m2 20.38 Stainless steel Riblath ref 267; 0.30mm thick 28.08 0.37 4.67 29.68 m2 34.35

10mm thick mesh lining to ceilings; ﬁxing with wire; to steelwork; over 300mm wide

Riblath ref 269; 0.30mm thick – 0.59 7.48 15.17 m2 22.65 Riblath ref 271; 0.50mm thick – 0.59 7.48 12.01 m2 19.49

M31 FIBROUS PLASTER

Fibrous plaster; ﬁxing with screws; plugging; countersinking; stopping; ﬁlling and pointing joints with plaster 16mm thick plain slab coverings to ceilings

over 300mm wide – – – – m2 106.31 not exceeding 300mm wide – – – – m 35.76

Coves; not exceeding 150mm girth per 25mm girth – – – – m 5.13

Coves; 150mm-300mm girth per 25mm girth – – – – m 6.28

Cornices per 25mm girth – – – – m 6.37

Cornice enrichments per 25mm girth; depending on degree of enrichments – – – – m 7.53

Fibrous plaster; ﬁxing with plaster wadding ﬁlling and pointing joints with plaster; to steel base 16mm thick plain slab coverings to ceilings

over 300mm wide – – – – m2 106.31 not exceeding 300mm wide – – – – m 35.76

16mm thick plain casings to stanchions per 25mm girth – – – – m 3.19

16mm thick plain casings to beams per 25mm girth – – – – m 3.19

Gyproc cove or other equal and approved; ﬁxing with adhesive; ﬁlling and pointing joints with plaster Cove

125mm girth – 0.19 2.67 1.35 m 4.02 Angles – 0.03 0.42 0.84 nr 1.26

Total £ hours £ £ rate £

M40 STONE/CONCRETE/QUARRY/CERAMIC TILING

ALTERNATIVE TILE MATERIALS Dennis Ruabon clay ﬂoor quarries (£/1000)

194mm×194mm×12.5mm; square; red – – – 432.21 1000 432.21 194mm×194mm×12.5mm; polygon; red – – – 32.04 m2 32.04 150mm×150mm×12.5mm; square; heatherbrown – – – 492.05 1000 492.05 150mm×150mm×12.5mm; studded square; heatherbrown or red – – – 716.80 1000 716.80 150mm×150mm×12.50mm; polygon; red – – – 45.78 m2 45.78

SUPPLY AND FIX PRICES

Clay ﬂoor quarries; BS EN 10545; class 1; Dennis Ruabon tiles or other equal and approved; level bedding 10mm thick and jointing in cement and sand (1:3); butt joints; straight both ways; ﬂush pointing with grout; to cement and sand base Work to ﬂoors; over 300mm wide

150mm×150mm×12.50mm thick; heatherbrown – 0.74 14.57 28.28 m2 42.85 150mm×150mm×12.50mm thick; red – 0.74 14.57 25.56 m2 40.13 194mm×194mm×12.50mm thick; heatherbrown – 0.60 11.81 22.72 m2 34.53

Works to ﬂoors; in staircase areas or plant rooms 150mm×150mm×12.50mm thick; heatherbrown – 0.83 16.34 28.28 m2 44.62 150mm×150mm×12.50mm thick; red – 0.83 16.34 25.56 m2 41.90 194mm×194mm×12.50mm thick; heatherbrown – 0.69 13.58 22.72 m2 36.30

Work to ﬂoors; not exceeding 300mm wide 150mm×150mm×12.50mm thick; heatherbrown – 0.37 7.28 7.32 m 14.60 150mm×150mm×12.50mm thick; red – 0.37 7.28 6.49 m 13.77 194mm×194mm×12.50mm thick; heatherbrown – 0.31 6.10 5.50 m 11.60 fair square cutting against ﬂush edges of existing ﬁnishes – 0.11 1.47 1.77 m 3.24 raking cutting – 0.19 2.57 2.00 m 4.57 cutting around pipes; not exceeding 0.30m girth – 0.14 1.97 – nr 1.97 extra for cutting and ﬁtting into recessed manhole cover 600mm×600mm – 0.93 13.05 – nr 13.05

Work to sills; 150mm wide; rounded edge tiles 200mm×150mm×22mm thick; interior; heatherbrown or red – 0.31 6.10 6.79 m 12.89 150mm×173mm×58mm thick; exterior; heatherbrown or red – 0.32 6.29 28.11 m 34.40

ﬁtted end – 0.14 1.97 – nr 1.97 Coved skirtings; 150mm high; rounded top edge

150mm×150mm×12.50mm thick; ref. CBTR; heatherbrown or red – 0.23 4.53 7.98 m 12.51 150mm×150mm×12.50mm thick; ref. RE; heatherbrown or red – 0.23 4.53 5.60 m 10.13

nr nr

Total £ hours £ £ rate £

M40 STONE/CONCRETE/QUARRY/CERAMIC TILING – cont

Glazed ceramic wall tiles; BS EN 10545; ﬁxing with adhesive; butt joints; straight both ways; ﬂush pointing with white grout; to plaster base Work to walls; over 300mm wide

152mm×152mm×5.50mm thick; white 11.76 0.56 11.02 13.15 m2 24.17 152mm×152mm×5.50mm thick; light colours 12.60 0.56 11.02 14.01 m2 25.03 152mm×152mm×5.50mm thick; dark colours 14.70 0.56 11.02 16.16 m2 27.18 extra for RE or REX tile – – – 5.60 m2 5.60 200mm×100mm×6.50mm thick; white and light colours 10.50 0.56 11.02 11.86 m2 22.88 250mm×200mm×7mm thick; white and light colours 12.60 0.56 11.02 14.01 m2 25.03

Work to walls; in staircase areas or plant rooms 152mm×152mm×5.50mm thick; white – 0.62 12.20 13.15 m2 25.35

Work to walls; not exceeding 300mm wide 152mm×152mm×5.50mm thick; white – 0.28 5.51 3.93 m 9.44 152mm×152mm×5.50mm thick; light colours – 0.28 5.51 4.37 m 9.88 152mm×152mm×5.50mm thick; dark colours – 0.28 5.51 5.01 m 10.52 200mm×100mm×6.50mm thick; white and light colours – 0.28 5.51 3.55 m 9.06 250mm×200mm×7mm thick; white and light colours – 0.23 4.53 4.19 m 8.72 cutting around pipes; not exceeding 0.30m girth – 0.09 1.26 – nr 1.26

Work to sills; 150mm wide; rounded edge tiles 152mm×152mm×5.50mm thick; white – 0.23 4.53 1.97 m 6.50 ﬁtted end – 0.09 1.26 – nr 1.26

198mm×64.50mm×6mm thick wall tiles; ﬁxing with adhesive; butt joints; straight both ways; ﬂush pointing with white grout; to plaster base Work to walls

over 300mm wide 26.46 1.67 32.86 28.22 m2 61.08 not exceeding 300mm wide – 0.65 12.79 8.45 m 21.24

20mm×20mm×5.50mm thick glazed mosaic wall tiles; ﬁxing with adhesive; butt joints; straight both ways; ﬂush pointing with white grout; to plaster base Work to walls

over 300mm wide 30.87 1.76 34.63 32.80 m2 67.43 not exceeding 300mm wide – 0.69 13.58 10.10 m 23.68

Total £ hours £ £ rate £

50mm×50mm×5.50mm thick slip-resistant mosaic ﬂoor tiles, Series 2 or other equal and approved; Langley London Ltd; ﬁxing with adhesive; butt joints; straight both ways; ﬂush pointing with white grout; to cement and sand base Work to ﬂoors

over 300mm wide 25.54 1.76 34.63 27.52 m2 62.15 not exceeding 300mm wide – 0.69 13.58 8.46 m 22.04

Dakota mahogany granite cladding; polished ﬁnish; jointed and pointed in coloured mortar (1:2:8) 20mm work to ﬂoors; level; to cement and sand base

over 300mm wide – – – – m2 303.19 20mm×300mm treads; plain nosings – – – – m 172.53 raking, cutting – – – – m 30.94 polished edges – – – – m 38.89 birdsmouth – – – – m 40.15

20mm thick work to walls; to cement and sand base over 300mm wide – – – – m2 309.30 not exceeding 300mm wide – – – – m 139.18

40mm thick work to walls; to cement and sand base over 300mm wide – – – – m2 513.56 not exceeding 300mm wide – – – – m 231.09

RivenWelsh slate ﬂoor tiles; level; bedding 10mm thick and jointing in cement and sand (1:3); butt joints; straight both ways; ﬂush pointing with coloured mortar; to cement and sand base Work to ﬂoors; over 300mm wide

250mm×250mm×12mm-15mm thick – 0.56 11.02 38.35 m2 49.37 Work to ﬂoors; not exceeding 300mm wide

250mm×250mm×12mm-15mm thick – 0.28 5.51 11.57 m 17.08

Roman Travertine marble cladding; polished ﬁnish; jointed and pointed in coloured mortar (1:2:8) 20mm thick work to ﬂoors; level; to cement and sand base

over 300mm wide – – – – m2 198.00 20mm×300mm treads; plain nosings – – – – m 119.27 raking cutting – – – – m 23.12 polished edges – – – – m 21.26 birdsmouth – – – – m 42.62

20mm thick work to walls; to cement and sand base over 300mm wide – – – – m2 235.44 not exceeding 300mm wide – – – – m 106.50

40mm thick work to walls; to cement and sand base over 300mm wide – – – – m2 324.10 m

Total £ hours £ £ rate £

M41 TERRAZZO TILING/IN SITU TERRAZZO

Terrazzo tiles; BS EN 13748; aggregate size random ground grouted and polished to 80's grit ﬁnish; standard colour range; 3mm joints symmetrical layout; bedding in 42mm cement semi-dry mix (1:4); grouting with neat matching cement 300mm×300mm×28mm (nominal) Terrazzo tile units; hydraulically pressed, mechanically vibrated, steam cured; to ﬂoors on concrete base (not included); sealed with penetrating case hardener or other equal and approved; 2 coats applied immediately after ﬁnal polishing

plain; laid level – – – – m2 41.40 plain; to slopes exceeding 15° from horizontal – – – – m2 50.46 to small areas/toilets – – – – m2 94.76

Accessories plastic division strips; 6mm×38mm; set into ﬂoor tiling above crack inducing joints, to the nearest full tile module – – – – m 2.86

Specially made terrazzo precast units; BS EN 13748-1; aggregate size random; standard colour range; 3mm joints; grouting with neat matching cement Standard tread and riser square combined terrazzo units (with riser cast down) or other equal and approved; 280mm wide; 150mm high; 40mm thick; machine-made; vibrated and fully machine polished; incorporating 1 nr. Ferodo anti-slip insert ref. OT40D or other equal and approved cast-in during manufacture; one end polished only

ﬁxed with cement: sand (1:4) mortar on prepared backgrounds (not included); grouted in neat tinted cement; wiped clean on completion of ﬁxing – – – – m 216.80

Standard tread square terrazzo units or other equal and approved; 40mm thick; 280mm wide; factory polished; incorporating 1 nr. Ferodo anti-slip insert ref. OT40D or other equal and approved

ﬁxed with cement: sand (1:4) mortar on prepared backgrounds (not included); grouted in neat tinted cement; wiped clean on completion of ﬁxing – – – – m 130.44

extra over for 55×55mm contrasting colour to step nosing – – – – m 45.59

Standard riser square terrazzo units or other equal and approved; 40mm thick; 150mm high; factory polished

ﬁxed with cemnt: sand (1:4) mortar on prepared m

Total £ hours £ £ rate £

Standard coved terrazzo skirting units or other equal and approved; 904mm long; 150mm high; nominal ﬁnish; 23mm thick; with square top edge

ﬁxed with cement: sand (1:4) mortar on prepared backgrounds (by others); grouted in neat tinted cement; wiped clean on completion of ﬁxing – – – – m 76.04

extra over for special internal/external angle pieces to match – – – – m 21.59 extra over for special polished ends – – – – nr 7.12

M42 WOOD BLOCK/COMPOSITION BLOCK/ PARQUET

Wood blocks; Havwoods or other equal and approved; 25mm thick; level; laid to herringbone pattern with 2 block borderl; ﬁxing with adhesive; to cement: sand base; sanded and sealed Work to ﬂoors; over 300mm wide

Merbau – – – – m2 97.81 Iroko – – – – m2 97.81 American Oak – – – – m2 102.51 European Oak – – – – m2 107.22

Add to wood block ﬂooring over 300mm wide for buff; one coat seal – – – – m2 3.76 buff; two coats seal – – – – m2 6.11 sand; three coats for seal or oil – – – – m2 16.93

M50 RUBBER/PLASTIC/CORK/LINO/CARPET TILING/SHEETING

Linoleum sheet; Forbo Flooring; laid level; ﬁxing with adhesive; welded joints; to cement and sand base Work to ﬂoors; over 300mm wide

Marmoleum Real marbled sheet, 2.0m wide; 2.50mm thick – 0.37 7.28 17.02 m2 24.30 Marmoleum Dual marbled tile 333mm×333mm×3.20mm thick – 0.45 8.86 20.76 m2 29.62 Decibel 17db marbled acoustic sheet, 2.0m wide; 3.50mm thick – 0.45 8.86 20.76 m2 29.62

High performance vinyl sheet; Forbo Flooring Eternal; laid level with welded seams; ﬁxing with adhesive; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick; 2.0m wide roll – 0.35 6.89 14.21 m2 21.10

Total £ hours £ £ rate £

M50 RUBBER/PLASTIC/CORK/LINO/CARPET TILING/SHEETING – cont

Slip-resistant vinyl sheet; Forbo Flooring Surestep; laid level with welded seams; ﬁxing with adhesive; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick; 2.0m wide roll – 0.37 7.28 14.21 m2 21.49

Anti-static vinyl tiles; Forbo Flooring Colorex SD; laid level; ﬁxing with adhesive; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick; 615mm×615mm tiles – 0.50 9.84 20.76 m2 30.60

Acoustic vinyl sheet; Forbo Flooring Sarlon Trafﬁc 19db; level with welded seams; ﬁxing with adhesive; to cement and sand base Work to ﬂoors; over 300mm wide

3.40mm thick; 2.0m wide roll – 0.37 7.28 17.02 m2 24.30

Vinyl sheet; Altro Safety range; with welded seams; level; ﬁxing with adhesive where appropriate; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick; Impressionist II – 0.74 14.57 16.01 m2 30.58 2.00mm thick; Marine – 0.56 11.02 14.17 m2 25.19 2.00mm thick; Suprema – 0.74 14.57 16.96 m2 31.53 2.00mm thick; Timbersafe II – 0.74 14.57 16.89 m2 31.46 2.00mm thick; Walkway – 0.56 11.02 11.65 m2 22.67 2.20mm thick; Xpresslay (NB No adhesive required) – 0.74 14.57 9.20 m2 23.77 2.50mm thick; Classic 25 – 0.65 12.79 15.86 m2 28.65 2.50mm thick; Maxis – 0.74 14.57 19.72 m2 34.29 2.50mm thick; Designer – 0.74 14.57 18.78 m2 33.35 3.50mm thick; Stronghold 30 – 0.74 14.57 21.40 m2 35.97

Vinyl sheet; Altro Sports surfaces range; with welded seams; level; ﬁxing with adhesive; to cement and sand base Work to ﬂoors; over 300mm wide

4.00mm thick; Mondoﬂex – 0.70 13.78 16.24 m2 30.02 4.50mm thick; Mondo Sportﬂex – 0.70 13.78 19.67 m2 33.45

Homogeneous Vinyl sheet; Marleyﬂor Plus or other equal and approved; level; with welded seams; ﬁxing with adhesive; level; to cement and sand base Work to ﬂoors; over 300mm wide

Total £ hours £ £ rate £

Safety sheet; Marleyﬂor Granite Multisafe or other equal and approved; level; with welded seams; ﬁxing with adhesive; level; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick – 0.42 8.26 12.64 m2 20.90

Vinyl sheet; Marleyﬂor Omnisports or other equal and approved; level; with welded seams; ﬁxing with adhesive; level; to cement and sand base Work to ﬂoors; over 300mm wide

7.65mm thick; Pro – 0.90 17.71 25.41 m2 43.12 8.75mm thick; Competition – 1.00 19.68 29.71 m2 49.39

Vinyl semi-ﬂexible tiles; Marleyﬂor Homogeneous tiles range; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

300mm×300mm×2.00mm thick; Vylon Plus – 0.23 4.53 5.59 m2 10.12 500mm×500mm×2.00mm thick; Marleyﬂor Plus – 0.20 3.94 6.79 m2 10.73

Vinyl tiles; Polyﬂex Plus; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

300mm×300mm×2.00mm thick – 0.23 4.53 6.04 m2 10.57

Vinyl tiles; Polyﬂex Camaro; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

300mm×300mm×2.00mm thick – 0.30 5.90 13.15 m2 19.05

Vinyl tiles; Polyﬂor XL; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

300mm×300mm×2.00mm thick – 0.32 6.29 7.44 m2 13.73

Vinyl sheet; Polyﬂor XL; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick – 0.28 5.41 5.22 m2 10.63

Vinyl sheet; Polysafe Standard; level; ﬁxing with adhesive; welded seams; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick – 0.28 5.41 9.29 m2 14.70 m2

Total £ hours £ £ rate £

M50 RUBBER/PLASTIC/CORK/LINO/CARPET TILING/SHEETING – cont

Vinyl sheet; Polysafe hydro; level; ﬁxing with adhesive; welded seams; to cement and sand base Work to ﬂoors; over 300mm wide

2.00mm thick – 0.28 5.41 11.90 m2 17.31

Luxury mineral vinyl tiles; Marley I D Naturelle; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

330mm×330mm×2.00mm thick – 0.23 4.53 8.94 m2 13.47

Acoustic vinyl tiles; Marley Tapiﬂex 243; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

500mm×500mm×2.00mm thick – 0.20 3.94 11.94 m2 15.88

Linoleum tiles; Marley Veneto XF; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

500mm×500mm×2.50mm thick – 0.20 3.94 14.08 m2 18.02

Cork tiles Wicanders Cork-Master; level; ﬁxing with adhesive; butt joints; straight both ways; to cement and sand base Work to ﬂoors; over 300mm wide

300mm×300mm×8.00mm thick; contract quality – 0.40 7.87 20.20 m2 28.07 300mm×300mm×6.00mm thick; high density – 0.40 7.87 20.63 m2 28.50 300mm×300mm×4.00mm thick; domestic – 0.37 7.28 15.42 m2 22.70

Rubber studded tiles; Altro Mondopave; level; ﬁxing with adhesive; butt joints; straight to cement and sand base Work to ﬂoors; over 300mm wide

500mm×500mm×2.50mm thick; type MRB; black – 0.56 11.02 22.00 m2 33.02 500mm×500mm×4.00mm thick; type MRB; black – 0.56 11.02 25.00 m2 36.02

Work to landings; over 300mm wide 500mm×500mm×4.00mm thick; type MRB; black – 0.74 14.57 25.00 m2 39.57

4.00mm thick to tread 275mm wide – 0.46 9.05 7.43 m 16.48

Total £ hours £ £ rate £

Sundry ﬂoor sheeting underlays For ﬂoor ﬁnishings; over 300mm wide

building paper to BS 1521; class A; 75mm lap (laying only) – 0.05 0.56 – m2 0.56 3.20mm thick hardboard – 0.19 3.74 1.41 m2 5.15 6.00mm thick plywood – 0.28 5.51 5.13 m2 10.64

Skirtings; plastic; Gradus or equivalent Set-in skirtings

100mm high; ref. SI1002.5P – 0.11 2.16 1.69 m 3.85 150mm high; ref. SI1502P – 0.22 4.33 2.55 m 6.88

Set-on skirtings 100mm high; ref. SO100P – 0.22 4.33 1.19 m 5.52

Stair nosings; aluminium; Gradus or equivalent Medium duty hard aluminium alloy stair tread nosings; plugged and screwed in concrete

56mm×32mm; ref AS11 7.77 0.23 3.23 8.01 m 11.24 84mm×32mm; ref AS12 10.75 0.28 3.93 11.06 m 14.99

Heavy duty aluminium alloy stair tread nosings; plugged and screwed to concrete

48mm×38mm; ref HE1 9.07 0.28 3.93 9.34 m 13.27 82mm×38mm; ref HE2 12.58 0.32 4.49 12.94 m 17.43

Carpet tiles to cement and sand base Work to ﬂoors over 300mm wide

Heuga 580 heavy duty loop pile 14.86 0.28 5.51 15.23 m2 20.74 Gradus Adventure range; bitumen backing; tufted pattern loop pile 18.90 0.28 5.51 19.37 m2 24.88 Latour/Predator ranges; bitumen backing; loop pile 9.93 0.28 5.51 10.18 m2 15.69

Door entrance mats Entrance mat systems; aluminium wiper bar; laying in position; 18mm thick

Gradus Topguard; 900mm×550mm – 0.46 5.20 130.02 nr 135.22 Gradus Topguard; 1200mm×750mm – 0.46 5.20 234.03 nr 239.23 Gradus Topguard; 2400mm×1200mm – 0.93 10.51 748.90 nr 759.41 Nuway Tuftiguard 500×1300 – – – – nr 227.50 Nuway Tuftiguard 1000×1600 – – – – nr 477.40 Nuway Tuftiguard 1800×3000 – – – – nr 1890.00 extra for brass wipers – – – 181.22 m2 181.22 Nuway Tuftiguard; single side aluminium scraper bar – – – – m2 350.00 Nuway Tuftiguard; double side aluminium rigidsctaper bars – – – – m2 500.00 Coral Classic textile secondary and circulation matting system; 2.0m wide roll – – – – m2 60.00 Coral Brush Activ secondary and circulation m2 wide m2

Total £ hours £ £ rate £

M50 RUBBER/PLASTIC/CORK/LINO/CARPET TILING/SHEETING – cont

Matwells Polished stainless steel matwell; angle rim with lugs; bedding in screed

Stainless steel frame bed in screed 500×1300mm – – – – nr 45.50 Stainless steel frame bed in screed 1000×1600mm – – – – nr 91.00 Stainless steel frame bed in screed 1100×1400mm – – – – nr 87.50 Stainless steel frame bed in screed 1800×3000mm – – – – nr 168.00

Polished aluminium matwell; angle rim with lugs brazed on; bedding in screed

900mm×550mm; constructed with 25×25×3mm angle 25.91 0.93 10.51 26.56 nr 37.07 1200mm×750mm; constructed with 34×26×6mm angle 43.36 1.00 11.30 44.44 nr 55.74 2400mm×1200mm; constructed with 50×50×6mm angle 166.10 1.50 16.94 170.25 nr 187.19

Polished brass matwell; comprising angle rim with lugs brazed on; bedding in screed

900mm×550mm; constructed with 25×25×5mm angle 57.93 0.93 10.51 59.38 nr 69.89 1200mm×750mm; constructed with 38×38×6mm angle 177.82 1.00 11.30 182.27 nr 193.57 2400mm x1200mm; constructed with 38×38×6mm angle 328.28 1.50 16.94 336.49 nr 353.43

M51 EDGE FIXED CARPETING

Fitted carpeting; Wilton wool/nylon or other equal and approved; 80/20 velvet pile; heavy domestic plain Work to ﬂoors

over 300mm wide 24.00 0.37 4.94 27.06 m2 32.00 Work to treads and risers

over 300mm wide – 0.74 9.88 27.06 m2 36.94

Fitted carpet; Forbo Flooring; Flocked ﬂooring Work to ﬂoors

Flotex classic textile; 2.0m wide roll – 0.45 7.81 23.57 m2 31.38 Flotex HD textile; 2.0m wide roll – 0.45 7.81 26.38 m2 34.19

Carpet tiles; Forbo Flooring; 500mm×500mm carpet tiles; adhesive applied to sub-ﬂoor Work to ﬂoors:

Teviot; low level loop pile; 2.50mm thick – 0.45 7.81 11.40 m2 19.21 Barcode; low level loop pile; 2.50mm thick – 0.45 7.81 17.02 m2 24.83 Circulate; random lay, batchless – 0.45 7.81 21.70 m2 29.51 Arran; textured loop; 4.00mm thick – 0.45 7.81 26.38 m2 34.19 m2

Total £ hours £ £ rate £

Fitted carpeting; Gradus broadloom polypropylene or other equal and approved Work to ﬂoors over 300mm wide

Bodega/Paciﬁc/Predator ranges, loop pile 10.63 0.37 4.94 10.90 m2 15.84 Genus/Volnay ranges, cut pile 17.96 0.33 4.45 18.41 m2 22.86

Work to treads and risers over 300mm wide – 0.74 9.88 17.61 m2 27.49

Underlay to carpeting Work to ﬂoors

over 300mm wide 1.86 0.07 0.93 1.91 m2 2.84 raking cutting – 0.07 0.79 – m 0.79

Sundries Carpet gripper ﬁxed to ﬂoor; standard edging

22mm wide – 0.04 0.45 0.22 m 0.67

M52 DECORATIVE PAPERS/FABRICS

Lining paper; and hanging Plaster walls or columns

over 300mm girth (PC £ per roll) 2.10 0.19 2.67 0.28 m2 2.95 Plaster ceilings or beams

over 300mm girth 2.10 0.23 3.23 0.28 m2 3.51

Decorative paper-backed vinyl wallpaper; and hanging Plaster walls or columns

over 300mm girth (PC £ per roll) 10.50 0.23 3.23 1.76 m2 4.99

PVC Wall lining; Altro Whiterock; or other equal and approved; ﬁxed directly to plastered brick or blockwork Work to walls over 300mm wide

Standard white – 1.00 14.03 32.78 m2 46.81 Satins – 1.00 14.03 39.37 m2 53.40 Stone – 1.30 18.25 56.88 m2 75.13 Illusions – 1.30 18.25 56.88 m2 75.13 Chameleon – 1.30 18.25 59.26 m2 77.51

M60 PAINTING/CLEAR FINISHING – EXTERNAL

BASIC PAINT PRICES Paints

matt emulsion 18.20 – – – 5 litres – gloss 21.92 – – – 5 litres – eggshell gloss 30.55 – – – 5 litres – oil-based undercoat 21.92 – – – 5 litres – Weathershield gloss 29.86 – – – 5 litres – litres

Total £ hours £ £ rate £

M60 PAINTING/CLEAR FINISHING – EXTERNAL – cont

BASIC PAINT PRICES – cont Paints – cont

Sandtex masonry paint brilliant white 10.78 – – – 5 litres – coloured 19.16 – – – 5 litres –

Primer/undercoats acrylic 15.32 – – – 5 litres – red oxide 22.16 – – – 5 litres – water-based 18.13 – – – 5 litres – zinc phosphate 34.38 – – – 5 litres – masonry sealer 15.29 – – – 5 litres – MDF primer 40.62 – – – 5 litres – knotting solution 43.30 – – – 5 litres –

Special paints solar reﬂective aluminium 35.78 – – – 5 litres – anti-grafﬁti 115.46 – – – 5 litres – bituminous emulsion 12.56 – – – 5 litres – Hammerite 41.44 – – – 5 litres – ﬁre retardant

undercoat 48.41 – – – 5 litres – top coat 64.48 – – – 5 litres –

Stains and Preservatives Cuprinol

Clear 23.41 – – – 5 litres – Boiled linseed oil 25.02 – – – 5 litres –

Sadolin Extra 42.86 – – – 5 litres – New Base 18.91 – – – 5 litres –

Sikkens Cetol HLS 45.12 – – – 5 litres – Cetol TS 68.82 – – – 5 litres – Cetol Filter 7 68.64 – – – 5 litres –

Protim Solignum Architectural 60.44 – – – 5 litres – Green 17.85 – – – 5 litres – Cedar 17.85 – – – 5 litres –

Varnishes polyurethane 32.75 – – – 5 litres –

Total £ hours £ £ rate £

SUPPLY AND FIX PRICES

NOTE: The following prices include for preparing surfaces. Painting woodwork also includes for knotting prior to applying the priming coat and for all stopping of nail holes etc.